RC tools and workshop buying guide: models, parts and compatibility
October 8, 2026
RC Tools and Workshop: What You Actually Need
A good RC workshop does not need to be big or expensive. What it needs is the right tools for the screws, nuts, and wiring in front of you, in good enough condition that they do not damage the parts you are trying to save. That matters even more with vintage RC. A rounded-out screw in a modern part is annoying. A rounded-out screw in a 30-year-old part you cannot easily replace can turn a simple rebuild into a parts hunt.
This guide suits anyone setting up a bench for the first time, anyone returning to the hobby with a box of old cars and no tools left, and anyone restoring vintage kits who has found that the drivers in the kitchen drawer will not cut it. It covers hand tools, setup tools, soldering and charging gear, and consumables. Start with the basics that fit your cars, buy decent quality where it counts, and add the rest as your work gets more involved.
The Main Categories
Hex drivers and nut drivers
These are the backbone of the bench. Most RC screws are socket-head screws driven by a hex driver, and most nuts, wheel nuts, and ball studs are turned with a nut driver. For metric cars, which is most Japanese and modern kits, the working hex sizes are 1.5mm, 2.0mm, and 2.5mm, with 3.0mm useful on larger hardware. For vintage American kits, you also need imperial drivers, most often .050 inch and 1/16 inch. Nut drivers around 5.0mm, 5.5mm, and 7.0mm handle most chassis nuts and wheel nuts.
Quality matters more here than anywhere else. A well-made driver, the kind MIP and a few other long-standing makers built their reputations on, is machined to a tight fit from steel that holds its edges. A cheap driver is often slightly undersized and softer. It feels fine for a few screws, then it slips and starts rounding the inside of the screw head. From then on, even a good driver struggles. If you buy one thing properly, buy your most-used hex drivers properly.
Pliers, cutters, and hand tools
- Needle-nose pliers for holding small parts, bending wire, and reaching into tight spaces
- Side cutters or flush cutters for zip ties and trimming parts off trees on new kits
- A hobby knife with fresh blades for trimming bodies and cleaning up parts
- Tweezers for shims, small screws, and e-clips that fingers cannot hold
- Small files or sanding sticks for deburring and easing sharp edges
- Ball-cup and turnbuckle tools where your cars use them, since pliers scar the plastic
Setup tools
Setup tools tell you what the car is actually doing instead of what you think it is doing. The essentials are a camber gauge, a ride height gauge, and calipers. Calipers earn their keep constantly: measuring screws, shafts, turnbuckle lengths, and mystery parts. Camber and ride height gauges matter most if you race or run on-road, but they also help on a restoration when you want both sides to match. A setup board and droop gauges are nice to have rather than necessary.
Soldering, charging, and bench basics
A temperature-controlled soldering iron, a stand, and proper solder will cover motor wires, battery leads, and connectors. For charging, you need a charger that matches your battery types, covered below. Round out the bench with a parts tray so screws stay sorted, good light, a stand that holds the car off its wheels, and small containers for separating hardware by car.
Compatibility, Rules, and Gotchas
The biggest gotcha in the workshop is metric versus imperial. Vintage American kits, especially older Associated, Losi, and similar designs, often used imperial hardware alongside or instead of metric. A 2.0mm driver feels close in a 1/16 inch screw, and a 1.5mm feels close in a .050 inch screw, but close is not fitting. The driver sits loose and rounds the screw out, sometimes on the first hard turn. If a driver feels sloppy, stop and check the size. On an unknown estate car or mixed parts box, expect both systems.
- Use threadlock sparingly and only where metal screws go into metal, such as pinions and some motor screws. A small drop of medium-strength threadlock is enough. Never use it on screws going into plastic, and keep it away from bearings and diffs. Too much, or the high-strength kind, can make a small screw effectively permanent.
- Match the connector to the job. Older cars ran Tamiya-style plugs, which are fine for mild use but were never great at handling high current and can get hot under load. Cars that will actually be driven are better served by a proper high-current connector, soldered well, with heat shrink over the joints. Standardize across your cars and chargers so adapters do not multiply.
- Solder joints should be shiny, smooth, and fully wetted. A dull, lumpy joint is a cold joint and will cause heat, resistance, and intermittent power. Do not move the joint while it cools.
- Never charge a battery on a setting meant for a different chemistry. NiMH and NiCd packs were the standard for vintage cars, and many older chargers only know those. LiPo packs need a LiPo-specific charger with balancing, on the correct mode, every time.
- Respect LiPo safety basics. Charge on a non-flammable surface, do not leave charging packs unattended, use the balance lead, put packs at storage charge if they will sit, and retire a pack that is puffed, damaged, or will not balance. An old NiMH pack that has sat for years should be cycled and checked before you trust it.
- Keep screws sorted by the car they came out of. Vintage hardware is not all standard, and mixing two cars’ screws into one pile creates hours of measuring later.
What Wears Out or Gets Lost First
Hex driver tips wear first, especially the small 1.5mm and .050 inch sizes, because there is so little metal there. Once the edges go, replace the tip before it ruins screws. Hobby knife blades dull quickly and should be changed often, since a dull blade makes you push harder and slip more. Side cutters get nicked if used on hardened wire, which ruins them for clean plastic work.
The things that vanish are predictable: the one driver size you use most, 2.0mm above all, e-clips that launch across the room, small body clips, and charger adapter leads. Consumables also run out mid-job, so keep spares of solder, heat shrink, threadlock, zip ties, double-sided tape for electronics, and shock oil in the weights you actually use.
Buying Used: An Inspection Checklist
Used tools are a smart way to build a bench, because good drivers and setup tools last for years and often come up in estate lots and hobby clear-outs. Check them like this:
- Look at hex driver tips under good light. Edges should be sharp and corners intact, not rounded, twisted, or ground at an angle.
- Test fit a driver in a known screw. It should sit snug with no rocking. A loose fit means the tip is worn or undersized.
- Check handles for cracks and shafts for bends. A bent shaft wobbles in the screw and cams out under torque.
- On nut drivers, look inside the socket for rounding and confirm the size marking is still readable.
- For calipers, close the jaws and confirm they read zero, then measure something known. Sticky or jumpy calipers are more trouble than they are worth.
- For a used soldering iron, power it up if you can. It should heat evenly and hold temperature. A pitted tip can be replaced, but price that in.
- For a used charger, confirm it supports the chemistries you run and check leads and balance ports for damage.
- Be skeptical of large no-name driver sets sold cheaply as complete. A few good drivers beat a case of soft ones.
Frequently Asked Questions
Do I really need both metric and imperial drivers?
If you only run modern or Japanese kits, metric alone covers nearly everything. If you work on vintage American cars, yes, you need both. The sizes overlap closely enough to tempt you and differently enough to damage screws. Having .050 inch and 1/16 inch drivers on hand is cheap insurance.
Can I use the charger that came with my old kit for LiPo batteries?
No. Older chargers made for NiCd and NiMH do not balance LiPo cells and do not end the charge the way LiPo requires. That is a fire risk, not just a performance issue. Use a charger with a proper LiPo balance mode.
Are power drivers a good idea for RC work?
A small electric screwdriver with an adjustable clutch can speed up long builds, but set the clutch low and always finish by hand. RC screws are small, many go into plastic, and too much torque strips threads and snaps screw heads before you feel it happening.
What is the first setup tool I should buy?
Calipers. Before camber gauges or setup boards, calipers answer questions on every job: screw length and diameter, shaft size, turnbuckle length, and whether two parts are actually the same.
Finding parts at ClodMod Racing
Alongside parts and kits, the store carries workshop tools, hardware, and bench supplies, and stock changes as lots come in. If you are building up a bench for a vintage project, check the ClodMod Racing store to see what is currently on hand, and ask if you are hunting for a specific driver size or tool that is not listed.